AutoFlow Automatic Balancing and FlowSet Manual Balancing Coil Hook-Up Modules may include:
- automatic balancing valves
- manual balancing valves
- strainers
- butterfly valves
- ball valves
- flanges
- unions
- pressure / temperature test ports
- air vents
- drain valves and
- fire and smoke rated hoses as well as others components
Basic Hook-Up Components
Model YC
1/2" - 2" Ball Valve and Y-Valve and Union – has a 20 mesh stainless screen and removable cap. Ball valve has PTFE packing, brass packing nut and stem, large diameter plated blowout proof ball. Viton O-ring type union with brass nut and tailpiece available in MPT, FPT, sweat male and female end connections. Rated at 400 PSIG @ 250 degrees F.
Submittal F171 Installation Specifications
Model YW
Y-Strainer with Port Section – Y-strainer, forged brass with 20 mesh stainless screen, removable access and drain cap. Tapped 1/4" FPT ports available for options. 1/2" - 2 1/2" with FPT ends and 1/2" - 1" with sweat ends. Rated at 400 PSIG @ 250°F.
Submittal F002 Installation Specifications
Model CW
2 1/2" - 4" Cast-Iorn Y-Strainer, Flanged – features machined tapered seat, ensures perfect fit for removable, stainless steel screen. 1/4" ports (as shown) available for options. All sizes come complete with flanged blow-off cover, gasket and plug. Install in vertical or horizontal pipe lines with blow-off connection at lower end of screen.
Submittal F217 Installation Specifications
Model UP
Union with Port Section – Brass construction. Viton O-ring union, brass nut and tailpiece. Available with threaded (MPT or FPT), solder or reducer end connections. Rated at 400 PSIG @ 250°F. May be ordered with factory installed options.See options list.
Submittal F169 Installation Specifications
Model BF
Butterfly Valve – 2" - 8" Cast iron lug-type butterfly valve. Infinite position handle with memory stop. Does not include mounting to other products, cap screws (CS).
Submittal F215 Installation Specifications
Model E2/E3
Two Position, Spring Return Control Valves – Motor drives valve open, spring closes. No flow with thermostat off. 24 volt or 120 volt with 18" leads.
Submittal F248 Installation Specifications
Model AC
1/2" - 2" AutoFlow regulator/ball valve/Port section/Union. Directional flow/Dual access ports. SWT or FPT (ball end) by SWT, FPT or MPT (union end). One reduction size available on union end - 1/2" - 2" SWT, FPT or MPT.
Submittal F172 Installation Specifications
Model YR
1/2" - 2 1/2" AutoFlow regulator/Port section/Directional flow/Dual access ports/Brass body. 1/2" - 1" SWT X SWT or FPT X FPT; 1 1/4" - 2 1/2" FPT X FPT. SWT X SWT available for 1 1/4" - 2" with addition of brass sweat adapters.
Submittal F001 Installation Specifications
Model UA
1/2" - 2" manual venturi valve with union option, large plated ball and PTFE seats. Blowout-proof stem with EPDM O-ring. Customary handles: Micro - A body, Standard - B and C bodies; memory stop, vinyl coated grip. Dual P / T ports with optional for air vent or drain valve. Union, fixed threaded, or sweat with metal-to-metal and EPDM O-ring.
Submittal F258 Installation Specifications
Model UB
1/2" - 2" shut-off Valve with Union Option with large diameter plated ball and PTFE seats. Blowout proof stem with EPDM O-ring. Micro handle on A body, standard handle on B and C bodies; optional adjustable memory stop for shut-off and resetting. Available - union or fixed threaded or sweat connections, metal-to-metal and EPDM O-ring seal.
Submittal F259 Installation Specifications
Pressure/Temperature Test Ports
with Superseal P/T plug features dual durometer EDPM (Nordel) internal seals and dual seal safety cap, with retaining strap. Single P/T Port, P/T Port w/ P/T extender, and Dual XL Ports for Kits A & B. Use Pressure/Temp Port in any device with port section. Regular - Hgt. = 1-1/4", Extended - Hgt. = 2-3/4". Rated 1000 psig at 270°F.
Submittal F119 Installation Specifications
Manual Air Vent
has a brass body and a blowout-proof needle style valve with a side vent. The knurled/slotted top can be sealed finger tight. Rated 400 psig at 250°F.
Knurled, slotted handle manual air vent, use with any port section device. Hgt = 1-1/2".
Submittal F201 Installation Specifications
Automatic Air Vent
is ideal for venting coils. It continuously vents air until the internal float rises to make a seal. The preferred location is on the inlet y-strainer. There is enough pressure drop and turbulence in the y-strainer to bring the air out of solution and vent it before it reaches the coil.
Submittal F006 Installation Specifications
Stem Extender
Use to extend accessories to clear 2" insullation (MPT x FPT 1/4" or 1/8"). Extends access valve, air vent, or blowdown.
Submittal F Installation Specifications
Memory Stop
Use for ball valve devices that do not come standard with memory stop.
Memory Stop for 1/2" - 2" Valves.
Submittal F Installation Specifications
Hose End Drain Valve
Hose End Drain Valve is a brass ball valve with chrome-plated ball, PTFE seats, plastic handle and a 3/4" hose outlet with cap. Rated 400 psig at 250°F.
Submittal F201 Installation Specifications
1/4" Mini-Ball Drain Valve
Mini-Ball Drain Valve has a brass body plastic handle and 1/4" FPT outlet connection. Rated 400 psig at 275°F.
Submittal F201 Installation Specifications
1/4" Dielectric Nipple
A dielectric water way preventing galvanic corrosion that normally occurs between dissimilar metals in the presence of water. The Model DN nipple:
- Allows six times less current than an insulated dielectric union
- Eliminates stray current corrosion
- Is lab tested and field proven
Submittal F201 Installation Specifications
Model FA
2" - 8" Accessory Flange – 150# ANSI raised face forged accessory steel flange can have a 1/4" FPT tap for P/T port, air vent, mini-ball valve and other accessories. 1/2" and 3/4" connections are available for larger drains and thermowells. Options can be at clock positions: 3, 6, 9 & 12. Available flange x weld (FA) or flange x groove (FG).
Submittal F255 Installation Specifications
Model FG
2" - 8" Accessory Flange – 150# ANSI raised face forged accessory steel flange can have a 1/4" FPT tap for P/T port, air vent, mini-ball valve and other accessories. 1/2" and 3/4" connections are available for larger drains and thermowells. Options can be at clock positions: 3, 6, 9 & 12. Available flange x weld (FA) or flange x groove (FG).
Submittal F255 Installation Specifications
Model GF
Accessory Flange Adapter – provides a direct transition from flanged components to grooved piping. Metal flange washer adapters are shipped with the unit and recommended for use with butterfly valves and serrated flange surfaces.
Submittal F255 Installation Specifications
Extended Handle
on ball valve products provides approximately 2" extra clearance for insulation.
Metal ID Tags
Tempered aluminum tag with chrome plated ball chain. Mylar label with etched writable information blocks.